American Standard Hot Tub 7242XXXW User Manual

7242.XXXW  
SERIES WHIRLPOOL  
RONDO™  
HIGH GLOSS ACRYLIC  
SHOWN LESS ALL FITTINGS  
INSTALLATION INSTRUCTIONS  
1816mm  
(71-1/2)  
RECOMMENDED FITTING  
165mm  
908mm  
(35-3/4)  
LOCATION 64 X 279mm  
(6-1/2)  
(2-1/2 X 11)  
THANK YOU...  
76mm  
(3)  
C/L OF DRAIN  
for selecting an American Standard bath. Your new  
bath is shipped to you after careful inspection. The  
whirlpool version is completely assembled with pump,  
motor, and system piping. All you need to finish the  
installation are your selected fittings and electrical  
connections for a whirlpool.  
267mm  
(10-1/2)  
229 X 305mm  
(9 X 12)  
CUTOUT  
PUMP  
1067mm  
(42)  
To insure maximum performance and pleasure from  
this product, please follow the instructions and  
cautions.  
ON/OFF  
SWITCH  
PROVIDE ACCESS  
TO PUMP FOR SERVICE  
ON ALL INSTALLATIONS  
OUTLINE OF  
CUTOUT  
List of Optional Components (not included):  
• Safe-T-Heater 9075.120*  
LEVELING STRINGER  
NOT FOR SUPPORT  
SAFE-T-HEATER  
REMOVABLE BLANK  
C/L OF  
OVERFLOW  
51mm  
(2)  
List of Required Components (not included):  
• Drain 1583.470*  
• Bath Filler*  
95mm  
(3-3/4)  
495mm  
(19-1/2)  
* see your Home Depot Retailer  
83mm  
(3-1/4)  
546mm  
(21-1/2)  
ROUGH  
38mm  
(1-1/2)  
FLOOR  
INTEGRAL  
FEET  
38 mm (1-1/2)  
TAILPIECE  
List of Required Tools and Supplies:  
GENERAL SPECIFICATIONS FOR 7242 WHIRLPOOL  
71-1/2 x 42 x 21-1/2 In (1816 x 1067 x 546mm)  
94 Lbs.(43 Kg.)  
INSTALLED SIZE  
WEIGHT  
Tools  
Supplies  
• Level  
• Nails  
818 Lbs.(371 Kg.)  
87 Gal. (330 L)  
67 Gal. (254 L)  
45 x 25 In. (1143 x 635mm)  
60 x 30 In. (1524 x 762mm)  
14-7/8 In (378mm.)  
WEIGHT w/WATER  
GAL. TO OVERFLOW  
WHIRLPOOL MIN. OPERATING VOL.  
BATHING WELL AT SUMP  
BATHING WELL AT RIM  
WATER DEPTH TO OVERFLOW  
FLOOR LOADING  
• Tape Measure  
• Pipe Wrench  
• Slip Joint Pliers  
• Screw Driver  
• Standard  
• Putty  
• Caulking (waterproof)  
• 1 x 3 or 2 x 2  
Stringers  
39 Lbs./Sq.Ft. (191 Kgs./Sq.m)  
• Drop Cloth  
• 20 amp GFI  
Outlet  
• Cement, Plaster,  
Grout  
(PROJECTED AREA)  
PTS.  
CUBE (FT3)  
Woodworking Tools  
• Personal Safety  
Equipment  
30.3  
58.7  
WHIRLPOOL ELECTRICAL SPECIFICATIONS  
PUMP  
2.1 HP, 14.4 AMPS,120.  
• Caulking Gun  
GENERAL INSTALLATION INFORMATION  
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor  
immediately.  
After inspection and during installation, protect the bath from construction damage. After installation, and before  
enclosing with wallboard, tile, etc., water test the unit and check for leaks.  
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect  
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,  
motor, or piping system.  
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and  
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead  
(required for recess installations).  
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.  
WARNING! Do not lift whirlpool by the piping harness at any time.  
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.  
© American Standard Inc. 2003  
All product names listed herein are trademarks  
of American Standard Inc. unless otherwise noted.  
751709-100 REV. L  
 
ELECTRICAL INSTALLATION INSTRUCTIONS  
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other  
applicable codes.  
WARNING:  
When using electrical products, basic precautions should always be observed, including the following:  
1. DANGER: RISK OF ELECTRIC SHOCK  
Connect only to a circuit protected by a ground-fault circuit interrupter.  
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.  
3. Install to permit access for servicing.  
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).  
The whirlpool should be installed on a 120 vac, 20 amp dedicated circuit. The circuit should be hard-wired from the  
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded  
neutral wire and a third wire, earth ground, are essential. ADDING THE SAFE-T-HEATER REQUIRES A SEPARATE  
15 AMP MAXIMUM GFCI CIRCUIT.  
ELECTRICAL INSTALLATION  
20 AMP GFCI  
OUTLET  
WHIRLPOOL MOUNTED  
120 VAC  
ELECTRONIC  
SWITCH  
PUMP/MOTOR  
GND.  
ELECTRICAL DIAGRAM  
READ AND FOLLOW ALL INSTRUCTIONS  
(3)  
751709-100 REV. L  
 
WIRE SELECTION GUIDE  
Maximum distance from  
fusebox to motor  
The sizes shown on this  
chart are recommendations  
for copper conductors  
only. Always follow  
local and national  
Motor  
Hi Performance  
Rating  
50'  
100'  
120V Power Line  
10  
150'  
200'  
electrical codes  
2.1  
12  
8
8
DRAIN CONNECTION AND SYSTEM TEST  
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the  
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of  
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings  
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is  
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the  
whirlpool is running.  
POST INSTALLATION CLEAN-UP  
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.  
Do not use wire brushes or any other metal implement on bath surface.  
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or  
®
stains may be removed using granular Spic and Span mixed with water.  
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.  
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.  
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing  
with a white automotive-type polishing compound and waxing with a liquid wax.  
®
(4)  
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE  
751709-100 REV. L  
 

3Com Switch 4500G User Manual
Acesonic Karaoke Machine KM 360 User Manual
Allied Telesis Network Router AT AR300 User Manual
AMC Stereo Amplifier XG16 User Manual
American Standard Door 4242STE1 User Manual
Atlantis Land Switch A07 ES3628C User Manual
Audiovox Automobile Alarm TSP 575 User Manual
Audiovox Stereo Amplifier AXT 240 User Manual
Bakers Pride Oven Convection Oven VGG CO User Manual
Barco Cell Phone Accessories 3 User Manual