Grizzly Nail Gun G6049 User Manual

14/15 GAUGE ANGLE FINISH  
NAILER KIT  
MODEL G6049  
INSTRUCTION MANUAL  
COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC.  
1821 VALENCIA ST., BELLINGHAM, WA 98227  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
PRINTED IN TAIWAN  
ONLINE MANUAL DISCLAIMER  
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CUR-  
RENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS  
ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE MACHINE, THIS MANUAL MAY NOT  
EXACTLY DEPICT YOUR MACHINE . CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT  
DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.  
 
Safety Instructions For Pneumatic Tools  
18. DISCONNECT TOOLS before ser-  
10. USE PROPER AIR HOSE for the  
tool. Make sure your air hose is in  
good condition and is long enough to  
reach your work without stretching.  
vicing and changing accessories.  
19. USE  
THE  
RECOMMENDED  
Consult the  
ACCESSORIES.  
owner’s manual for recommended  
accessories. The use of improper  
accessories may cause risk of  
injury.  
11. WEAR PROPER APPAREL. Do not  
wear loose clothing, gloves, neck-  
ties, rings, bracelets, or other jewel-  
ry which may get caught in moving  
parts. Non-slip footwear is recom-  
mended. Wear a protective hair cov-  
ering to contain long hair.  
20. CHECK  
DAMAGED  
PARTS.  
Before further use of the tool, a  
guard or other part that is damaged  
should be carefully checked to  
determine that it will operate prop-  
erly and perform its intended func-  
tion. Check for alignment of moving  
parts, binding of moving parts,  
breakage of parts, mounting, and  
any other conditions that may affect  
its operation. A guard or other part  
that is damaged should be properly  
repaired or replaced.  
12. ALWAYS USE SAFETY GLASSES.  
Also use a face or dust mask if cut-  
ting operation is dusty. Everyday  
eyeglasses only have impact resis-  
tant lenses, they are NOT safety  
glasses.  
13. WEAR APPROVED HEARING  
PROTECTION.  
14. SECURE WORK. Use clamps or a  
vise to hold work when practical. It is  
safer than using your hand and frees  
both hands to operate tool.  
21. NEVER LEAVE UNATTENDED  
TOOL CONNECTED TO AIR.  
Disconnect the air hose and do not  
leave tool until it is relieved of any  
built up pressure.  
15. DO NOT OVERREACH. Keep prop-  
er footing and balance at all times.  
16. MAINTAIN TOOLS WITH CARE.  
Keep tools lubricated and clean for  
best and safest performance. Follow  
instructions for lubricating and  
changing accessories.  
22. NEVER ALLOW UNTRAINED  
USERS TO USE THIS TOOL  
WHILE UNSUPERVISED.  
23. IF YOU ARE UNSURE OF THE  
INTENDED OPERATION, STOP  
USING THE TOOL. Seek formal  
training or research books or maga-  
zines that specialize in pneumatic  
tools.  
17. REDUCE THE RISK OF UNINTEN-  
TIONAL STARTING. Do not carry  
tool with hand on trigger and always  
disconnect from air when not in use.  
-2-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
Basic Nailer Safety  
In addition to the rules stated in the previ-  
ous section, and those in the warning  
boxes throughout this manual, please  
observe the following safety tips for your  
new nailer:  
1. READ THIS ENTIRE MANUAL  
BEFORE OPERATING THE NAIL-  
ER.  
2. ALWAYS DISCONNECT AIR FROM  
THE NAILER whenever servicing or  
installing nails. During maintenance,  
a nailer connected to air may fire acci-  
dentally, causing serious personal  
injury.  
3. DO NOT PLACE HANDS NEAR  
NAIL POINT OF ENTRY. Nail can  
deflect and be driven through the sur-  
face of the workpiece, puncturing  
your hand or fingers.  
Operating this nailer can propel  
objects into the air, causing immedi-  
ate eye damage. To protect yourself,  
always wear American National  
Standards Institute (ANSI) approved  
safety glasses or goggles when oper-  
ating this equipment. In addition, this  
nailer discharges at 85-90 decibels.  
To protect your hearing, always wear  
ANSI approved ear protection when  
operating this nailer.  
4. NEVER CONNECT THE NAILER TO  
PRESSURIZED  
OXYGEN  
OR  
OTHER COMBUSTIBLE GASES as  
a power source. Only use filtered,  
lubricated, and regulated compressed  
air.  
5. ALWAYS  
KEEP  
ANY  
BYSTANDERS BEHIND NAILER  
OR AWAY FROM AREA DURING  
USE. Nails may be driven completely  
though wood and could become dan-  
gerous projectiles.  
6. DO NOT CARRY THE NAILER BY  
ANY OTHER PART THAN THE  
HANDLE, and do not carry the nailer  
by the air hose.  
7. DO NOT KEEP THE TRIGGER  
PULLED ON THE SAFETY YOKE  
MECHANISM WHEN CARRYING  
OR HOLDING THE TOOL.  
Never point this nailer at yourself or  
another person! Always pay attention  
to the direction this nailer is pointed.  
Use this tool with respect and caution  
to lessen the possibility of operator or  
bystander injury. Ignoring this warn-  
ing may result in serious personal  
injury.  
8. DO NOT USE A CHECK VALVE OR  
ANY OTHER FITTING that allows air  
to remain in the tool.  
-3-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
INTRODUCTION  
Most important, we stand behind our tools.  
Commentary  
If you have any service questions or parts  
requests, please call or write us at the  
location listed below.  
We are proud to offer the Grizzly Model  
G6049 14/15 Gauge Angle Finish Nailer.  
This model is part of a growing Grizzly  
family of fine power tools. When used  
according to the guidelines set forth in this  
manual, you can expect years of trouble-  
free, enjoyable operation and proof of  
Grizzly’s commitment to customer satis-  
faction.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
The Model G6049 features a 360˚  
adjustable exhaust, a quick release nose  
clamp, a convenient side-loading maga-  
zine, a safety trigger and a durable plastic  
carrying case. The Model G6049 shoots  
14/15 gauge brad nails 114"-212" in length  
and accepts up to 100 nails at a time. At  
4.8 lbs., this model is also easy to carry  
around for hours.  
We are pleased to provide this manual  
with the Model G6049. It was written to  
encourage safety considerations and  
guide you through general operating pro-  
cedures and maintenance. This manual  
represents our effort to produce the best  
documentation possible.  
Read the manual before assembly  
and operation. Become familiar with  
this tool, its safety instructions, and  
its operation before beginning any  
work. Serious personal injury may  
result if safety or operational infor-  
mation is not understood or followed.  
The specifications, details, and pho-  
tographs in this manual represent the  
Model G6049 as supplied when the man-  
ual was prepared. However, owing to  
Grizzly’s policy of continuous improve-  
ment, changes may be made at any time  
with no obligation on the part of Grizzly. If  
you have any comments regarding this  
manual, please write to us at the address  
below:  
Grizzly Industrial, Inc.  
Technical Documentation  
P.O. Box 2069  
C
/O  
Bellingham, WA 98227-2069  
-4-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
Compressed Air System  
Safety Yoke Mechanism  
The Model G6049 is designed to be oper-  
ated at 80-120 psi. Do not exceed the  
maximum operating pressure!  
A safety yoke mechanism (bump fire) on  
the nose of the nailer acts as a safety  
device. When the trigger is pressed, the  
nailer will not fire until the safety yoke  
mechanism is depressed.  
Before you use your new nailer, regulate  
the air pressure on your air compressor to  
barely over the minimum psi for your nail-  
er. Increase air pressure only if needed.  
Before you use your nailer for the first time,  
check the safety yoke mechanism to  
ensure proper function. To do this:  
Many pneumatic tools benefit from an in-  
line filter/lubricator/regulator unit. This  
attachment is connected by hoses  
between the air compressor and the nailer.  
Using this unit protects your tool from dam-  
aging water build-up, allows you to adjust  
and maintain constant air pressure to your  
tool, and saves you the inconvenience of  
having to manually lubricate your tool  
every time you use it. Check the current  
Grizzly catalog for availability of this unit. If  
you plan on installing a filter/lubricator/reg-  
ulator unit in your compressed air system,  
always follow the connection instructions  
that come with the unit.  
1. Make sure the nailer is disconnect-  
ed from the air supply!  
2. Make sure the magazine is empty and  
contains no nails.  
3. Make sure the trigger and the safety  
yoke mechanism move up and down  
without sticking.  
4. Connect the nailer to the air supply.  
5. Without pressing the trigger,  
depress the safety yoke mechanism  
against a scrap piece of wood that is  
clean and free of any knots, nails, or  
other foreign objects. If the nailer  
does not fire, then the safety yoke  
mechanism is working correctly. If the  
nailer does fire when you do this,  
immediately disconnect the nailer  
from the air supply and call our cus-  
tomer service for help.  
Similarly if the nailer fires when the trigger  
is pulled, without the safety yoke mech-  
anism being depressed, then the nailer is  
not working properly.  
If either of these two conditions develop  
after you have used your nailer for a peri-  
od of time, check the lubrication of these  
mechanisms.  
Exceeding the maximum permissible  
operating pressure may cause the  
nailer to explode, blowing metal frag-  
ments in all directions. To protect  
yourself from serious personal injury,  
DO NOT allow your air compressor to  
exceed the recommended pressure  
when connected to this nailer!  
The safety yoke is a mechanical  
device that can fail. Never rely on the  
safety yoke mechanism as an excuse  
to point the nailer at yourself or any  
bystanders. Serious injury may occur.  
-5-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
OPERATION  
Single/Bump Fire Mode  
Loading Nailer  
The Model G6049 is equipped with a sin-  
gle/bump fire trigger.  
To load your nailer:  
1. Disconnect the air supply from the  
nailer!  
To select single or bump fire operation:  
2. Load nails at the top of the magazine  
in the T-slot as shown in Figure 1.  
1. Disconnect the air supply from the  
nailer!  
2. Locate the hex nut that secures the  
safety yoke mechanism to the trigger  
housing. See Figure 2.  
3. To select Single Fire mode, tighten  
the hex nut completely.  
4. To select Bump Fire mode, unthread  
the hex nut at least two full turns.  
Figure 1. Loading the nailer (side view  
and end view). Match nail heads with  
head slot for insertion.  
Adjustment  
Hex Nut  
3. Slide the stick of nails all the way  
down to the nose of the nailer.  
4. Pull the magazine pusher all the way  
back, then let it come forward until it  
catches on the end of the nail stick.  
Figure 2. Single/bump fire adjustment.  
When replacing nails for your Model  
G6049, follow these guidelines:  
Gauge: 14/15  
Length: 114"-212  
"
Capacity: 100 Nails  
-6-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
Besides damaging your workpiece,  
deflection can cause injury if your free  
hand is securing the workpiece in the  
location that the nail deflects.  
Operating Nailer  
If you have not read the safety instruc-  
tions in this manual, do not operate the  
nailer.  
4. Press the trigger. If the nail drove into  
the wood far enough, continue with  
your intended operations. If the nail  
either went too far or not far enough,  
adjust the depth.  
Periodically, place one drop of the included  
oil into the quick connect fitting where the  
nailer connects to the air supply. After oil-  
ing, wipe off any excess oil near the nailer  
exhaust to avoid dust build-up.  
Adjusting Depth  
To operate your nailer:  
The side of the magazine houses a knurled  
adjustment knob (illustrated in Figure 4)  
for setting the depth that the nailer drives  
nails into the workpiece.  
1. Connect the air supply to the quick  
connect fitting.  
2. Test the loaded nailer for proper pen-  
etration. Hold the nailer perpendicular  
to the surface of a piece of clean  
scrap wood that is thick enough for  
the length of nails you have loaded.  
Depress the safety yoke mechanism  
on your workpiece.  
3. Before pressing the trigger, make  
sure your free hand is positioned out  
of the way of a potential path of a nail  
in case of deflection. (Deflection is  
caused when the nail changes its  
path, resulting in the nail puncturing  
the surface of the workpiece as  
shown in Figure 3.)  
Figure 4. Depth adjustment knob.  
Figure 3. Example of nail deflection.  
-7-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
To clear a jammed nail from the discharge  
area with the Model G6049:  
Clearing Jammed Nails  
The most frequent situation with any type  
of nailer is a nail jam. A jammed nail must  
be cleared before using the nailer again.  
1. Disconnect the nailer from the air  
supply!  
2. Push the finger tab inside the maga-  
zine pusher, pull the pusher back  
slightly to clear it from the nail stick  
and allow it to come all the way for-  
ward, near the nose.  
3. Push down the backstop inside the  
magazine and slide the nail stick out  
of the back of the magazine.  
4. Flip up the quick release latch located  
on top of the nailer nose assembly as  
shown in Figure 5.  
5. Remove the driver guide cover.  
6. The jammed nail should now be visi-  
ble; remove it from the discharge area  
with needle nose pliers.  
Always disconnect air from nailer  
whenever clearing a jammed nail!  
7. Replace the driver guide cover and  
snap the quick release latch back into  
operating position.  
Quick  
Release  
Latch  
Driver  
Guide  
Cover  
Figure 5. Removing guide cover.  
-8-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
Oiling Nailer  
Cleaning Nailer  
The Model G6049 is considered an oil-less  
model. This means it features a teflon pis-  
ton ring that does not require oil to operate.  
However, periodic applications of oil will  
extend the useful life of the piston assem-  
bly.  
Use a good solvent to clean the nose  
assembly of the nailer. Always be sure that  
the nailer is dry before using it again.  
Do not allow dust, chips, sand, etc. into the  
air connectors or into the body of the nail-  
er; this may result in leaks and damage to  
the nailer and the air fittings.  
Special oil has been included with you new  
Grizzly Nailer. Periodically place one drop  
of oil in the nailer air inlet (as shown in  
Figure 6). After oiling, wipe off any excess  
oil near the nailer exhaust to avoid dust  
build-up. When the oil that was included  
with the nailer has been completely used,  
replace with Grizzly Model G2820  
Pneumatic Tool Oil.  
Another option to manual oiling would be  
to install a lubricator in your air compressor  
line. If your air compressor line already has  
a lubricator, then regular lubrication of your  
nailer will not be necessary. Just make  
sure there is always oil in the lubricator.  
Never use gasoline or other flamma-  
ble liquids to clean this tool. Vapors  
in the tool may ignite, causing the  
tool to explode. Ignoring this warning  
may lead to serious personal injury or  
even death!  
As mentioned before, the best option is to  
install a filter/lubricator/regulator unit such  
as the Grizzly Model H2333 in your air line.  
Figure 6. Lubricating nailer via air inlet.  
Always disconnect air from nailer  
whenever servicing! During mainte-  
nance, a nailer connected to air may  
fire accidentally, causing serious  
personal injury!  
NOTICE  
Too much oil in the nailer will ruin  
the O-rings!  
-9-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
Replacing Pistons/O-Rings  
If you use your nailer day in and day out,  
Grizzly offers repair pistons as cheap  
insurance against wasted down time and  
lost profits in the event that a piston or pis-  
ton shaft becomes worn out. To replace a  
piston:  
Figure 7. Removing nailer exhaust cap.  
8. With a long flathead screwdriver or  
similarly shaped tool, push the piston  
shaft back inside the nailer until you  
can grip the piston head and remove  
it from the cylinder. (Be careful not to  
scratch the discharge area when  
pushing the piston shaft with the  
screwdriver.)  
9. Place a new O-ring on the new piston  
and apply a thin film of the nailer lubri-  
cating oil on the O-ring.  
Always disconnect air from nailer  
whenever servicing! During mainte-  
nance, a nailer connected to air may  
fire accidentally, causing serious  
personal injury!  
10. Insert the new piston in the cylinder.  
Make sure that the grooves on the  
piston shaft line up with those on the  
guide at the bottom of the cylinder.  
The new piston should easily slide  
into the cylinder. Do not force the  
piston into the cylinder! If the piston  
is not easily inserted, double-check  
the alignment of the piston shaft with  
the grooves on the guide.  
1. Disconnect the nailer from the air  
supply!  
2. Remove all nails from the magazine  
cartridge.  
3. Remove the 4 cap screws from the  
nailer exhaust cap.  
4. Remove the exhaust cap as shown in  
Figure 7.  
11. After the piston is inserted correctly,  
close the magazine. Replace the rear  
cap assembly and tighten the 4 cap  
screws.  
5. The top of the piston should now be  
visible inside the cylinder, which is  
housed in the head of the nailer.  
6. Open the magazine.  
12. For more assistance, or to install a  
complete O-ring set, refer to the  
breakdown diagram in the back of this  
manual.  
7. Watch the discharge area and push  
the top of the piston with your finger.  
You will see the piston shaft slide  
down the discharge area.  
-10-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
G6049 PART BREAKDOWN  
-11-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
01 P6049001 LOCK NUT  
02 P6049002 EXHAUST COVER  
03 P6049003 SPRING PLATE  
05A P6048005A CAP SCREW SW  
06 P6049006 CAP  
42 P6049042 PLUNGER  
43 P6049043 O-RING  
44 P6049044 PLUNGER CAP  
45B P6048045B TRIGGER ASSEMBLY  
46 P6049046 O-RING  
07A P6048007A BUTTON HD CAP SCR  
08 P6049008 SPACER  
47A P6044047A O-RING  
48A P6049048A LATCH  
09 P6049009 PISTON STOPPER  
10 P6049010 SPRING  
49 P6048049 BALL PIN  
50A P6049050A GUIDE COVER ASM  
50 P6049050 NOSE COVER  
51 P6049051 NOSE  
11 P6049011 O-RING  
12 P6049012 PISTON HEAD VALVE  
13 P6049013 O-RING  
52A P6049052A SET BLOCK  
53 P6049053 SAFETY ADJUST NUT  
54 P6049054 WAVE WASHER  
55 P6049055 SAFETY LEVER  
56A P6049056A SPRING  
14 P6049014 SEAL  
15A P6048015A O-RING  
16A P6049016A PISTON ASSEMBLY  
18 P6049018 CYLINDER SPACER  
19 P6049019 O-RING  
57 P6049057 ROLLER  
20 P6049020 O-RING  
58 P6049058 PUSHER  
21 P6049021 CYLINDER  
22 P6049022 BUMPER  
23 P6049023 WASHER  
24 P6049024 GASKET  
59 P6049059 TOR. SPRING  
60 P6049060 BALL PIN  
62 P6049078 PUSHER GUIDE  
63 P6049063 MAGAZINE  
64 P6049064 SLEEVE  
25 P6049025 BODY  
26 P6049026 E RING  
65 P6049065 SET PLATE  
66A P6049066A CAP SCREW  
67A P6049067A LOCK NUT  
68A P6048068A LOCK NUT  
69 P6049069 LOCK NUT  
70 P6049070 GASKET  
27 P6049027 GASKET  
28 P6049028 STEPPED PIN  
29 P6049029 BOTTOM  
29-1 P6048029-1 O-RING  
30A P6048030A CAP SCREW  
31 P6049031 SPRING GUIDE  
32A P6049032A SAFETY LEVER  
33 P6049033 SPRING  
71 P6049071 REAR COVER  
72 P6049072 AIR PLUG  
74A P6044075 CAP SCREW SW  
76A P6049076A BUTTON HD CAP SCR  
77 P6049077 NAIL GUIDE LINER  
83 P6049083 SPRING  
34 P6049034 SAFETY LEVER  
35A P6049035A ROLLED PIN  
36 P6049036 O-RING  
37 P6049037 VALVE  
86 P6049086 STOPPER  
88 P6049088 MAGAZINE CAP  
90 P6049090 BRACKET  
92A P6044077 FLAT WASHER  
93 P6049093 RUBBER PAD  
38 P6049038 O-RING  
39 P6049039 O-RING  
40 P6049040 O-RING  
41 P6049041 VALVE PLUNGER  
-12-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
TROUBLESHOOTING  
CAUSE  
PROBLEM  
ACTION  
1. O-rings in trigger valve  
housing are damaged.  
1. O-rings must be replaced  
& operation of safety  
yoke must be checked.  
Air leaking at trigger valve  
area.  
1. Loose screws in housing.  
2. Damaged O-ring.  
3. Loose air fitting.  
1. Tighten screws.  
2. Replace O-ring.  
3. Tighten air fitting.  
Air leaking between hous-  
ing and hose.  
1. Damaged seal.  
1. Air leaks.  
1. Replace damaged seals.  
Air leaking between hous-  
ing and cap assembly.  
1. Tighten screws and fit-  
tings.  
Tool skips nails while dis-  
charging.  
2. Dirt in nose.  
2. Clean nose.  
3. Dirt or damage prevents  
nails from moving freely in  
magazine.  
3. Clean magazine and  
inspect/repair damage.  
4. Inadequate air flow to tool.  
4. Check fitting, hose, com-  
pressor & air pressure.  
5. Replace piston O-ring.  
Lubricate.  
5. Worn O-ring on piston or  
lack of lubrication.  
6. Damaged O-rings on trigger  
valve.  
6. Replace trigger valve O-  
rings.  
7. Worn bumper.  
8. Cap seal leaking.  
7. Replace bumper.  
8. Replace cap seal.  
1. Nailer is not sufficiently lubri-  
1. Lubricate nailer.  
2. Replace spring.  
Tool runs slowly or has a  
loss of power.  
cated.  
2. Broken spring in cap assem-  
bly.  
3. Exhaust port in cap is  
blocked.  
3. Clean or replace dam-  
aged internal parts.  
1. Nails are the wrong size.  
2. Nails are bent.  
3. Magazine or nose screws  
are loose.  
1. Use correct nails.  
2. Use undamaged nails.  
3. Tighten magazine and  
nose screws.  
Fasteners frequently jam  
the nailer.  
4. Driver or driver guide are  
worn or damaged.  
4. Replace worn or dam-  
aged parts.  
5. Nails are wrong angle.  
5. Use correct angle nails.  
1. Nail is jammed in maga-  
zine or discharge area.  
1. Clear nailer magazine or  
discharge area.  
Nailer does not fire.  
2. Piston shaft is damaged.  
3. Air pressure too low.  
2. Replace piston shaft.  
3. Check/increase air pres-  
sure.  
G6049 14/15 Gauge Angle Finish Nailer Kit  
-13-  
 
WARRANTY AND RETURNS  
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original  
purchaser from the date of purchase. This warranty does not apply to defects due directly  
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-  
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be  
implied by law, including any merchantability or fitness, for any particular purpose, are here-  
by limited to the duration of this written warranty. We do not warrant or represent that the  
merchandise complies with the provisions of any law or acts unless the manufacturer so  
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price  
paid for the product and any legal actions brought against Grizzly shall be tried in the State  
of Washington, County of Whatcom.  
We shall in no event be liable for death, injuries to persons or property or for incidental, con-  
tingent, special, or consequential damages arising from the use of our products.  
To take advantage of this warranty, contact us by mail or phone and give us all the details.  
We will then issue you a “Return Authorization Number,” which must be clearly posted on  
the outside as well as the inside of the carton. We will not accept any item back without this  
number. Proof of purchase must accompany the merchandise.  
The manufacturers reserve the right to change specifications at any time because they con-  
stantly strive to achieve better quality equipment. We make every effort to ensure that our  
products meet high quality and durability standards and we hope you never need to use this  
warranty.  
Please feel free to write or call us if you have any questions about the machine or the man-  
ual.  
Grizzly Industrial, Inc.  
1203 Lycoming Mall Circle  
Muncy, PA 17756  
Phone: (570) 546-9663  
Fax: (800) 438-5901  
E-Mail:  
Thank you again for your business and continued support. We hope to serve you again  
soon!  
-14-  
G6049 14/15 Gauge Angle Finish Nailer Kit  
 
WARRANTY CARD  
Name__________________________________________________________  
Street__________________________________________________________  
City____________________State________Zip_________  
Phone Number____________E-Mail___________________FAX____________  
Model #_______________Serial#________________Order #______________  
The following information is given on a voluntary basis. It will be used for marketing purposes to help  
us develop better products and services. Of course, all information is strictly confidential.  
9. How many of the machines checked above are  
Grizzly? ____________  
1. How did you learn about us?  
___Advertisement  
___Friend  
___Catalog  
___World Wide Web  
___Other__________________________  
___Card Deck  
10. Which portable/hand held power tools do you own?  
Check all that apply.  
___Belt Sander  
___Biscuit Joiner  
___Circular Saw  
___Detail Sander  
___Drill/Driver  
___Orbital Sander  
___Palm Sander  
___Portable Planer  
___Saber Saw  
___Reciprocating Saw  
___Router  
2. What is your annual household income?  
___$20,000-$29,999  
___$30,000-$39,999  
___$40,000-$49,999  
___$50,000-$59,999  
___$60,000-$69,999  
___$70,000-$79,999  
___$80,000-$89,999  
___$90,000 +  
___Miter Saw  
___Other_________________________________  
3. What is your age group?  
___20-29  
11. What machines/supplies would you like Grizzly  
Industrial to carry?  
___50-59  
___60-69  
___70 +  
___30-39  
___40-49  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
4. How long have you been a woodworker?  
___0 - 2 Years  
___2 - 8 Years  
___8 - 20 Years  
___20+ Years  
12. What new accessories would you like Grizzly  
Industrial to carry?  
5. How would you rank your woodworking skills?  
________________________________________  
________________________________________  
________________________________________  
________________________________________  
___Simple  
___Advanced  
___Intermediate  
___Master Craftsman  
6. What stationary woodworking tools do you own?  
Check all that apply.  
13. What other companies do you purchase your tools  
and supplies from?  
___Air Compressor  
___Band Saw  
___Panel Saw  
___Planer  
_________________________________________  
_________________________________________  
_________________________________________  
___Drill Press  
___Power Feeder  
___Radial Arm Saw  
___Shaper  
___Jointer  
___Lathe  
___Drum Sander  
___Dust Collector  
___Spindle Sander  
___Table Saw  
14. Do you think your purchase represents good value?  
___Yes  
___No  
___Mortiser  
___Wide Belt Sander  
___Horiz.Boring Machine  
___Vacuum Veneer Press  
___Other______________________________  
15. Would you recommend Grizzly to a friend?  
___Yes ___No  
16. Would you allow us to use your name as a refer-  
ence for Grizzly customers in your area? Note: We  
never use names more than three times.  
7. How many of your woodworking machines are  
Grizzly? _____________  
___Yes  
___No  
8. Which benchtop tools do you own? Check all  
that apply.  
17.Comments:________________________________  
_________________________________________  
_________________________________________  
_________________________________________  
___1"x42" Belt Sander ___6" - 8" Grinder  
___5" - 8" Drill Press ___Mini Lathe  
___8" Table Saw  
___Scroll Saw  
___8" - 10" Bandsaw  
___Disc/Belt Sander  
___Spindle/Belt Sander ___Mini Jointer  
___10"-12"Thickness Planer  
___Other______________________________  
 
Send a Grizzly Catalog to a friend:  
Name________________________________  
Street________________________________  
City______________State______Zip_______  
FOLD ALONG DOTTED LINE  
Place  
Stamp  
Here  
GRIZZLY INDUSTRIAL, INC.  
P.O. BOX 2069  
BELLINGHAM, WA 98227-2069  
TAPE ALONG EDGES--PLEASE DO NOT NAIL  
 

Graco Heat Pump 233500 User Manual
Grundig Electric Shaver MS 3540 User Manual
Hamilton Beach Mixer Drink Mixer User Manual
Harbor Freight Tools Tool Storage 90320 User Manual
Heath Zenith Work Light SL 5592 User Manual
Honeywell Weather Radio T675A User Manual
Hotpoint Ventilation Hood HXB9LSX User Manual
HP Hewlett Packard Sprinkler 182T User Manual
Humax TV DVD Combo PAU42THD User Manual
IKEA Plumbing Product AA 322687 2 User Manual