DUST COLLECTOR
ACCESSORY KIT
93601
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvement, actual product may differ slightly from product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
10.
Always check hardware and assembled parts after assembling. All connections should
be tight and hardware tightened.
11.
12.
Caution: Avoid sharp edges during use and assembly.
Beware of operating the power tool in explosive atmospheres, such as in the
presence of flammable liquids, gases, or sawdust. Electrical products create sparks
which may ignite sawdust released from the Dust Collector, as well as other dust and fumes.
13.
Carefully inspect the condition of the accessory before use and check the accessory
continually during use. If any damage is noted, stop immediately and replace the
accessory with an undamaged one. Harbor Freight Tools cannot be held responsible
for damage caused by using a damaged accessory on this product.
14.
15.
Keep the hoses away from sharp objects and excessive heat.
Make sure to read and understand all instructions and safety precautions, as outlined in the
manufacturer’s manual of the power equipment to which the Dust Collector Accessory Kit
will be attached.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activites, contain chemicals known [to the State of California] to cause cancer,
birth defects or other reproductive harm. some examples of these chemicals are:
•
•
•
Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles. (California Health & Safety Code 25249.5, et seq. )
Warning:
The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking your Dust Collector Accessory Kit, check to make sure all parts listed on page 5
are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at
1-800-444-3353.
Product Overview
The Dust Collector Accessory Kit is designed to be attached to one or two power tools, and is used
for the collection of wood dust, wood chips, sand, and other light debris. The Dust Collector
Accessory Kit may be attached to table saws, band saws, sanders, router tables, shapers, jointers,
and a variety of dust collecting machines all having a 4” dust port. Due to the wide diversity of
power machinery to which the Dust Collector Accessory Kit may be attached, it is recommended
that only a qualified technician perform the assembly procedure.
SKU 93601
For technical questions please call 1-800-444-3353.
Page 3
Assembly
1.
2.
Though the Dust Collector Accessory Kit is designed to offer a wide variety of applications, the
following illustration depicts a typical assembly method to hook-up one power equipment tool
and two power equipment tools-see Figure 1 below.
Note: The Dust Collector Accessory Kit is designed to be attached to stationary power
equipment tools and dust collectors having 4” diameter dust ports. Depending on the
diameter of the dust port of your power equipment tools and dust collector, it may be
necessary to attach size adapters (not included) to ensure a proper fit.
Figure 1-To Attach to One or Two Power Tools
Attaching to One Power Tool
Jointer Hood (6” square) (3)
4” Diameter Blast Gate (2)
or
4”Wire Hose Clamp (6)
Table Saw Dust Hood (12’square) (5)
Dust
Port
Dust
Port
Dust
Collector
Flexible Hose (1)
Attaching to Two Power Tools
“Y” Fitting (4)
Power
Tool
Power
Tool
3.
4.
5.
Check the length of Flexible Hose (1) needed to set up the Dust Collector Accessory Kit with
your power tool. It may be necessary to cut the Flexible Hose (1). To cut the Flexible
Hose (1), cut the plastic on the hose in a straight line between one coil of wire. Use a tin
snip or wire cutter to cut the coil inside the hose.
Place a Wire Hose Clamp (6) over the Flexible Hose. Slide the Flexible Hose (1) onto the
dust port. Slide the Wire Hose Clamp (6) so that it sits on both a section of Flexible Hose (1)
and the dust port. Thread down the screw on the Wire Hose Clamp (6) until the Flexible
Hose (1) is tight on the dust port.
Open and close the Blast Gate (2) to control the air flow from the Power Tool(s) to the dust
collector. When this kit is attached to 2 power tools, always close the Blast Gate (2) of an
unused dust collector hose.
SKU 93601
For technical questions please call 1-800-444-3353.
Page 4
Inspection, Maintenance and Cleaning
1.
2.
CAUTION: Prior to performing any inspection, maintenance, or cleaning of the Dust
Collector Accessory Kit, make sure to turn OFF and then disconnect the power tool from the
outlet.
BEFORE EACH USE, inspect the general condition of the Dust Collector Accessory Kit.
Check for loose connections, misalignment or binding of moving parts, cracked, torn, or
broken parts, and any other condition that may affect its safe operation. If abnormal noise or
vibration occurs, have the problem corrected before further use. Do not use damaged
equipment.
3.
4.
DAILY: With a soft brush, cloth, or vacuum, remove all debris from the Dust
Collector Accessory Kit. If necessary, you may use a mild detergent.
Clean the hoses periodically by standing it on end and tapping it to remove dust and debris.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Parts List
Part #
Description
Quantity
1
2
3
4
5
6
Flexible Hose, 4” x 10’
Blast Gate-4” x 4”
Jointer Hood-6”
“Y” Fitting-4” x 4” x 4”
Table Saw Dust Hood 12” x 12” 1
2
2
2
1
Wire Hose Clamp
10
Parts Diagram
1
6
2
5
3
4
SKU 93601
For technical questions please call 1-800-444-3353.
Page 5
|