1 HP cast Iron
sewage PumP
66351
set uP, oPeratIng, and maIntenance
InstructIons
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe tHIs manual.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 09i
ductor in the cord is the grounding
wire. Do not connect the green or
green and yellow wire to a live termi-
nal.
d. do not operate this sewage
Pump if either the Power cord (1),
Power Plug (29), Housing (10), or
Base (27), appear cracked or dam-
aged in any way.
e. warnIng! do not repair a dam-
aged power cord. always replace
the cord before further use of this
sewage Pump.
f. do not place this sewage Pump
in water with bare hands. always
wear heavy-duty, insulated rubber
gloves.
Your unit has a plug as illustrated
above. The outlet used should look
like the outlet illustrated above. do
not remove the grounding prong
from the plug. If the plug will not
fit the outlet, have a proper outlet
installed by a qualified electrician.
g. do not attach the power plug to
electrical outlet until the sewage
Pump is placed where it will re-
main during operation.
h. always unplug the sewage Pump
before touching, moving, inspect-
ing, or servicing.
5. WARNING: Handling the cord on
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
2. Keep children away when assem-
bling, setting up, inspecting and/or
servicing this sewage Pump.
3.
Wear ANSI-approved safety
goggles, heavy-duty insu-
lated rubber work gloves
and rubber boots while working with
or around this Sewage Pump.
General and Specific Safety
1. warnIng: to prevent serious per-
sonal injury and/or death to your-
self and/or others:
4. Do not Overreach - Keep proper foot-
ing and balance at all times.
5. Stay Alert - Watch what you are do-
ing. Use common sense.
a. do not use this sewage Pump to
pump any flammable, or explosive
fluids, such as gasoline, fuel oil,
kerosene, etc.
b. DO NOT use in flammable, and/or
explosive atmosphere.
c. use this sewage Pump only with
liquids compatible with pump
component materials.
SKU 66351
For technical questions, please call 1-800-444-3353.
Page 3
product, but must be supplied by the
operator.
drip loop
outlet
saVe tHese
InstructIons.
deVIce
sPecIFIcatIons
cord
Electrical Information 120 V, 60 Hz, 10.5 AMPS
6. Use Drip-Loop to prevent water from
accidentally entering the electrical
power outlet. Use only with a GFCI
outlet. see second paragraph in
“Power cord safety” section of
this manual.
Gallons Per Minute
Pump Motor
110
1 HP, 3450 RPM
unPacKIng
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
use and care
1. When servicing use only identical
replacement parts.
2. Do not use this Sewage Pump for
any job except that for which it is
intended.
set uP InstructIons
3. disconnect the sewage Pump from
the power supply when not in use,
or before inspection and/or ser-
vice/storage.
read the entIre ImPortant
saFety InstructIons
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
4. Store Idle Sewage Pump Indoors
when not in use out of reach of chil-
dren.
to
PreVent
serIous
5. Maintain labels and nameplates on
the appliance. These carry important
safety information. If unreadable or
missing, contact Harbor Freight Tools
for a replacement.
Injury From accIdental
oPeratIon:
unplug the sewage Pump
from its electrical outlet
before assembling,
inspecting, making any
adjustments, or servicing.
6. The warnings, precautions, and in-
structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
note: For additional information regarding
the parts listed in the following pages,
SKU 66351
For technical questions, please call 1-800-444-3353.
Page 4
refer to the Assembly Diagram near
the end of this manual.
oPeratIng InstructIons
read the entIre ImPortant
saFety InFormatIon section
at the beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
assemBly
1. Thread a discharge hose, or pipe
(not supplied) to the orifice on side of
Base (27).
1. Before operating the Sewage Pump,
put on ANSI-approved safety gog-
gles and other safety gear including
heavy-duty, insulated rubber gloves.
Safety goggles and other safety gear
are sold separately.
2. If you use a check-valve (not sup-
plied), mount the check valve hori-
zonally or at 45°. The valve pivot
should be on top. NOTE: If the
check valve should be mounted in a
vertical position, solid waste will tend
to lodge on top of the valve flapper
preventing it from opening.
2. Install the Sewage Pump firmly on it’s
Legs and supported by rigid hose, or
pipe discharge fixtures to eliminate
twisting and damage from motor
torque during operation.
3. If using a check-valve, drill a 1/16”
hole in the discharge hose, or pipe 1”
to 2” above the Base (27). The hole
will prevent an air lock in the Mo-
3. After installation, allow the Sew-
age Pump to flood with water before
plugging Power Cord (1) into outlet.
This will help prevent over heating
from running the Motor (18) with no
water resistance moving through the
Sewage Pump. Once this Sewage
Pump is plugged into a 120 Volt GFCI
outlet, the Motor (18) will start auto-
matically.
tor (18) both at start up and/or if the
Sewage Pump should lose its prime.
4. After the check-valve, a (full-port)
gate-valve (not supplied), which will
pass 2” solid waste should be in-
stalled in the system. The gate-valve
allows removal of the Sewage Pump
for cleaning and service.
note: If you do not feel qualified to
completely (and safely) install this
sewage Pump, it is recommended
that you have it installed by a
qualified plumber, or service tech-
nician.
4. This Sewage Pump is designed to
transfer waste water in cycles.
Rev 09i
SKU 66351
For technical questions, please call 1-800-444-3353.
Page 5
warnIng: this sewage Pump contains
dielectric motor oil for both lubri-
cation and heat transfer. It may be
under pressure because of heat
collection. let the sewage Pump
cool for at least 2 hours before
inspecting, or servicing. this oil
may be dangerous to the environ-
ment. always dispose of used oil
in compliance with all local, state
and Federal rules and regulations.
maIntenance and
serVIcIng
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
to PreVent
serIous Injury
From accIdental
oPeratIon or electrIc
sHocK:
unclogging the Impeller (24).
unplug the sewage Pump
from its electrical outlet
before performing any
accessory change, inspection,
maintenance, and/or cleaning
procedures.
1. Unplug the Sewage Pump, put on
heavy-duty insulated rubber gloves
and ANSI-approved safety goggles.
2. Remove the discharge hose, or pipe.
3. Lift Sewage Pump out of water using
the Handle (5).
to PreVent serIous
Injury From tool
FaIlure:
do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
4. To unclog the Impeller (24), remove
5 Screws (28) on the Sewage Pump
bottom and remove Base (27).
5. Flush the Impeller (24) with clean,
lukewarm water.
6. Reinstall the Impeller (24) and re-
place the Base (27) using the 5
Screws (28).
cleaning, maintenance, and
lubrication
7. Using the Handle (5), replace the
Sewage Pump into water in original
position.
1. BeFore use and PerIodIcally
tHereaFter, inspect the gen-
eral condition of the Sewage Pump.
Check for loose screws, misalignment
or binding of moving parts, cracked or
broken parts, damaged electrical wir-
ing, and any other condition that may
affect its safe operation.
8. Re-thread the discharge pipe, or
hose.
9. Plug the Sewage Pump back into the
120 Volt, GFCI power outlet.
2.
warnIng! If the supply cord of
this appliance is damaged, it must
be replaced only by a qualified
service technician.
10. The Sewage Pump will start auto-
matically.
SKU 66351
For technical questions, please call 1-800-444-3353.
Page 6
troubleshooting
Problem
Possible causes
likely solutions
1. Check power at outlet.
Sewage Pump will not 1. No power at outlet.
start.
2. Circuit breaker tripped.
2. Check circuit breaker for outlet.
3. Check that cord is plugged in.
4. Check water level.
3. Cord not connected.
4. Water level too low.
Low flow from
1. Possible excess solid debris lodged 1. Check and clean debris from
discharge outlets.
Sewage Pump starts
and stops too often.
in Impeller.
1. Possible back flow from discharge
pipe and/or hoses.
Impeller per instructions on Page 6.
1. Install a check-valve.
2. Check-valve either not installed, or if 2. Remove and examine check-valve
installed, it is leaking.
for proper installation and operation.
Replace if necessary.
Sewage Pump
operates but delivers
little or no water.
1. Low line voltage.
1. If voltage is under recommended
minimum, check wiring size from the
main switch on property. If not OK,
contact local power company.
2. Debris caught in Impeller or
discharge hoses or pipes.
2. Remove and check Impeller and
discharge hoses or pipes. Clean if
needed.
3. Check-valve stuck closed or
installed backwards.
3. Remove and examine check-valve
and reinstall correctly or replace.
Follow all safety precautions whenever diagnosing or servicing the
appliance. disconnect power supply before service.
Please read tHe FollowIng careFully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIEDAND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
REV 09i
SKU 66351
For technical questions, please call 1-800-444-3353.
Page 7
Parts lIst
Parts lIst
Part
description
Q’ty
1
2
1
2
1
1
1
1
1
1
2
1
4
1
Part
description
Q’ty
1
2
3
4
5
6
7
8
9
Power Cord
17 Motor Shaft
1
1
1
1
1
1
1
1
6
1
1
5
1
Screw 3/16 - 24 x 1/4
Cord Cover (Protector)
Screw 1/4 - 20 x 1/4
Handle
Washer 3/16
Strain Relief
18 Motor
19 Washer 6202zz - 12.7
20 Mechanic Seal Typ 21
21 O-Ring
22 Motor Seat
23 V-Seal
Screw 3/16 24 x 308
1/4” NPT Oil Plug
24 Impeller
25 Flat Screw 3/16 - 24 x 5/8
26 Packing Gasket
27 Base
28 Screw 1/4 - 20 x 3/4
29 Power Plug
10 Pump Motor Housing
11 Washer 3/16 x 1/4
12 Capacitor 40uf/350 V Vac
13 Screw M4 x 130
14 Rear Cover
15 Washer
2
16 Washer 608zz
1
assemBly dIagram
SKU 66351
For technical questions, please call 1-800-444-3353.
Page 8
lImIted 90 day warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESS-
LY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
record Product’s serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 66351
For technical questions, please call 1-800-444-3353.
Page 9
|